居家大小事，找它有丿步-小工匠工程網
LIANSUO CONSTRUCTION TECHNOLOGY CO., LTD.
店家文章分享
Firestop Design for High-Rise Building Curtain Wall Gaps: A Study Based on ASTM E2393 Inspection Standards
High-rise buildings often experience significant dynamic displacement under extreme conditions such as earthquakes. Curtain wall systems, in particular, are more susceptible to gap failures due to their structural flexibility. A firestop system must not only ensure fire resistance but also accommodate multi-directional movement to maintain continuous fire separation. However, the current Taiwan CNS standards primarily address firestopping for penetrations like pipes and cables, lacking specific testing regulations for curtain wall gaps. This presents a significant safety risk.
As an internationally recognized inspection standard for firestop systems, ASTM E2393 establishes clear guidelines for firestopping in high-rise building curtain wall gaps. Below is an overview of the key requirements of this standard:
ASTM E2393 Inspection Standards
Scope of Inspection
This standard applies to all types of firestop systems and perimeter joint protection in buildings, including joints between fire-resistant structural components and between fire-rated floors and non-fire-rated walls.
Documentation Requirements
Inspectors must receive complete documentation at least ten working days before the inspection, including project specifications, contract drawings, approved designs, engineering judgments, manufacturer instructions, and applicable building codes.
Material Verification
- Inspectors must verify that firestop materials have been tested in accordance with ASTM E1966 or UL 2079 and comply with relevant standards.
- All materials must bear quality assurance labels from recognized certification bodies.
Construction Quality
- Firestop materials must be uniformly applied and securely bonded to the structural components.
- Inspectors should observe the installation process, document substrate and material measurements, or conduct destructive testing to verify compliance.
Dynamic Adaptability
- Firestop systems must maintain their sealing effectiveness under multi-directional displacement, such as those caused by earthquakes.
- Materials should have excellent flexibility, elongation, and fire resistance. Sufficient expansion space should be reserved at curtain wall joints to prevent cracks or detachment during seismic movement.
Fire Resistance Integrity
- Firestop materials must maintain their designed fire resistance rating even after structural vibrations.
Inspection Procedures
Inspection Frequency
The frequency of inspections depends on the method and project scope. It may include random inspections during installation or post-installation sampling.
Random Sampling During Installation
- Inspectors must randomly check at least 5% of firestop joint systems during the installation process.
Post-Installation Sampling
- A minimum of one sample per 500 linear feet of each joint system type must be inspected after installation.
- Destructive or disassembly verification methods should be used for validation.
Non-Compliance Handling
- If 10% or more of the inspected firestop systems fail to meet standards, the inspection should be halted. The installation team must correct or replace non-compliant systems before re-inspection.
Defect Documentation
- All identified defects must be recorded in inspection reports and reported to the contractor for corrective action.
- Repaired systems must undergo re-inspection within two days.
Final Report
- Upon completion of installation and inspection, the inspector must submit a final report detailing project information, inspector and installer credentials, and a summary of inspection results.
Design and Construction Recommendations
Based on the above requirements:
- Firestop materials should have excellent flexibility, elongation, and fire resistance.
- Sufficient expansion space should be reserved at curtain wall joints to prevent cracks or detachment during earthquakes.
- During construction, strict adherence to ASTM E2393 and other international standards is essential.
- Random inspections should be conducted to ensure firestop system effectiveness under extreme conditions.
Professional Inspection Services
As an IAS/iLac internationally accredited firestop inspection agency, Liansuo Construction Technology provides professional inspection services following ISO 17020 standardized procedures. We conduct comprehensive evaluations of firestop systems for curtain wall gaps in high-rise buildings and issue internationally certified third-party inspection reports based on ASTM E2393. Our reports offer technical guidance and rectification recommendations, effectively enhancing fire safety standards.
Conclusion
Firestop design for curtain wall gaps in high-rise buildings is a critical aspect of seismic and fire protection. Quality control must be maintained throughout material selection, structural design, construction, and on-site inspection. Liansuo Construction Technology, with its international certifications and extensive experience, is committed to bridging the gaps in Taiwan’s standards, reinforcing high-rise building seismic and fire protection, and safeguarding lives and property.
其它相關店家資訊
免責聲明本網站僅提供工程公司資訊參考平台， 並不涉入其中任何諮詢、交易。本網站對各該工程公司相關資訊亦不作任何實質或形式上之審查。就本網站中所載一切工程公司的資訊、文字、照片、圖形 、產權、廣告內容、或其他資料（以下簡稱『內容』），無論其為公開張貼或私下傳送，若有不實或違法情事，均為『內容』提供者之責任，本站概不負責也不承擔任何法律責任